(888) 929-3610
Affordable Wireless Solutions

Power Injectors

These Power Injectors are manufactured by Cambium, CyberData, EnGenius, Laird, LigoWave, Maxxwave, MikroTik, Peplink, Sikly, Tycon Power, and Ubiquiti Networks.

Items 1 to 10 of 66 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Grid  List 

Set Ascending Direction
  1. AT-16-56V240W PoE Texas Gigabit 16-Port PoE Injector with Dual 56V 240 Watt Power Supply

    PoE Texas Gigabit 16-Port PoE Injector with Dual 56V 240 Watt Power Supply

    $331.99

    PoE Texas Gigabit 16-Port PoE Injector with Dual 56V 240 Watt Power Supplies is 802.3af/at compliant Power over Ethernet (PoE) injector takes power from the included 56 volt DC power supplies and adds it to an Ethernet data cable (Cat5, Cat5e, Cat6) to power your PoE devices. Power is only added to the data cable when an 802.3af or 802.3at device is connected.
    Specifications
    • Certifications N/A • Data + PoE Ports 16 • Data Ports: 16 • Data Rate: Gigabit • Dimensions: 19x2x1.75 in. • LEDs Per Port: 1 • Max Amps Per Kit 4 Amps • Max Power for Kit 240 Watts • Max. Amps Per Port: 650 mA • Mount Type: Rack • Operating Humidity: 5% to 90% • Operating Temperature Range: -10 - 60C • Output Voltage: 44 volts to 56 volts • PoE Configurable Per Port: No • PoE Method: Active • PoE Mode/Pin-out Mode A (-1,2 +3,6) • PoE Standard: IEEE 802.3at • Power Input: 2.1 mm DC and Phoenix Connector 1840382 • Power Supplies: WS-PS-56v120w x 2 Learn More »
  2. I0ATPI44 SAF Tehnika GbE PoE Universal Programmable Injector w/Built-In DC-DC Adaptor 24-60V

    SAF Tehnika GbE PoE Universal Programmable Injector w/Built-In DC-DC Adaptor 24-60V

    $240.00

    SAF Tehnika GbE PoE Universal Programmable Injector w/Built-In DC-DC Adaptor 24-60V is an indoor Power over Ethernet injector. It provides Gigabit Ethernet and power via single Ethernet cable (Cat5e or better). This solution allows running just one cable from inside equipment to the radio outside instead of using two separate cables for power and Ethernet. For CFIP Lumina radios it must be used together with PoE splitter. The PoE injector has a built-in lightning and surge protection preventing transient over-voltages from damaging radio and user’s indoor equipment. The injector is protected against reversed polarity. The injector has a built-in DC/DC converter, which is always active, thus input voltage can vary from 20 to 65 V, but it will be stabilized to 54 V on the output. Device has an over current and short circuit protection. It is designed to diminish the negative influence of long cable or insufficient input voltage from power supply. Features • Input voltage as low as 20 V DC and up to 65 V DC • Built in PoE controller, complies with IEEE 802.3af, IEE 802.3at and PoE++. • 1000 Base-T Ethernet • Cat5e and Cat6 compatibility • Lightning and surge protection on all lines • Surge voltage protection from improper grounding • Auto PoE++ mode as factory default • Manual modes with four current limits switchable: 0.75, 1.0, 1.25 and 1.7A • Tested compliance to IEC 61000-4-5
    Specifications
    • Data rate Up to 1000 Mb/s • DC/DC Mode Always active • Input Voltage 20 – 65 V • Output Voltage 54 V • Max Output Current in Auto PoE++ mode 1.2 A (UIN 22…36V DC) • 1.6 A (UIN 36…60V DC) • Switchable Current limits in PoE Manual modes 0.75, 1.0, 1.25 and 1.7A • Current limit in Forced mode (not recommended) 2.0 A • Power Connector 2ESDV-02P with screw locks • Ethernet Connectors Shielded RJ45 jacks • Data Lines Pins (1, 2), (3, 6), (4, 5) and (7, 8) • Power Lines + (1, 2) and (4, 5); - (3, 6) and (7, 8) • Power Clamping Voltage +/- 70 V • Max data cable length 100 m • Ports RJ45 - Data • RJ45 - Data + Power • DC - 2ESDV-02P socket with screw locks* • Grounding screw • Dimensions (W/H/D): 82 mm/41 mm/154 mm • Weight 0.4 kg • Enclosure Steel • Operating Temperature -10ºC to +50ºC • Mounting With bracket (included) • 19” rack mounting shelf (p/n I0KTPI11.003) • DIN-rail clip (p/n I0STPI11.01)
    Product Data Sheet
    I0ATPI44 Data Sheet Learn More »
  3. GPOE-16A-48V240W PoE Texas Gigabit 16-Port PoE Injector with Dual 48V 120 Watt Power Supply

    PoE Texas Gigabit 16-Port PoE Injector with Dual 48V 120 Watt Power Supply

    $233.99

    PoE Texas Gigabit 16-Port PoE Injector with Dual 48V 120 Watt Power Supply can power IP cameras, desktop phones, WiFi access points, or other low voltage devices through a network data cable using this Power over Ethernet (PoE) injector. The PoE Injector takes power from the 48 volt power supply and adds it to the Ethernet data cable (Cat5, Cat5e, Cat6) to your device.
    Specifications
    • Certifications UL/CE/FCC • Data + PoE Ports: 16 • Data Ports: 16 • Data Rate: Gigabit • Dimensions: 20x4x1.75 in. • Max Amps Per Kit 2.5 Amps • Max Power for Kit 240 Watts • Max. Amps Per Port: 650 mA • Mount Type: rack • Operating Humidity: 5% to 90% • Operating Temperature Range: -10 - 60C • Output Voltage: 48 volts • PoE Method: Passive • PoE Mode/Pinout Mode A (-1,2 +3,6) • Power Input: 2.1mm DC x2 • Power Supplies: WS-PS-48v120w x 2 Learn More »
  4. TP-MS4G-VHP Tycon Power 4 Port Very High Power Gigabit Mid Span Passive PoE Injector

    Tycon Power 4 Port Very High Power Gigabit Mid Span Passive PoE Injector

    $208.95

    The TP-MS4G-VHP mid span PoE power source is used for supplying PoE and data to multiple devices from a central location such as an operations room or equipment cabinet. The PoE device features a seperate data-in port coupled with a data out/PoE port. The PoE function is considered 4 Pair Passive PoE which is sometimes referred to as "High Poe". The units support Gigabit Ethernet and are backward compatible to 10/100MB. The Midspan features Universal Voltage (UniVolt) PoE outputs where the PoE voltage equals the input voltage. All ports will have the same PoE voltage. PoE DC Voltage (20-60V) is supplied on pins 1,2 (V-), 3,6 (V+) and 4,5 (V+) and 7,8 (V-). The unit can accept + or - voltage on input however the design is a non isolated design. Maximum power output per port is 1.8A. The individual output are overcurrent, over/under voltage and short circuit protected. The midspan is DIN Rail mountable with the included DIN Rail brackets. Product Features • Very High Power, Gigabit 4 Port Midspan PoE Injector • Up to 1.8A per Individual Port • Universal PoE Votlage 20VDC to 60VDC • Powers Passive PoE Devices using 4 Pair Power • DIN Rail Mountable - Includes DIN Rail Adapters Product Applications • High PoE Wireless Access Points and Client Devices • High PoE Security Camera Systems • Power Network Devices from a Central Network Room Product Specifications • Ethernet Standard: IEEE802.3/IEEE802.3u/IEEE802.3ab (10base-T/100base-T/1000base-T) • PoE Standard: Passive PoE, 4 Pair Power, High PoE • PoE Pinout: 1,2 (V-) 3,6 (V+) and 4,5 (V+) 7,8 (V-) • Shielded RJ45 Ports: 4 data-in; 4 data/PoE out, Port shield is connected to FG (frame ground) • Max Device Distance: 100m (328ft) • Maximum Device Distance: 100m (328ft) • Maximum PoE Power: Up to 1.8A per Port • PoE Protection: Over Current, Over/Under Voltage, Short Circuit • LED's:    - Green: A valid power device is detected on this port. Active Current is >100mA    - Red: No power device is detected on this port    - Off: No input power, or input source in alarm condition    - Alarm: Voltage is more than 65VDC, or less than 15VDC, or current is >2A • DC Power Input: 20VDC to 60VDC, Unit can accept + or - VDC on input, non-isolated design, Fused at 10A • Self Consumption: <1W • Operating Temperature: -30 to 60°C (-40 to 140°F) • Operating Humidity: Up to 90%, Non Condensing • Storage Temperature: -40 to 85°C (-40 to 185°F) • Dimensions: 90 x 118 x 40mm (3.5 x 4.6 x 1.5") • Weight: 0.45kg (1lbs) Product Documentation TP-MS4G-VHP Datasheet Learn More »
  5. PoE Texas Gigabit 16-Port PoE Injector with 48V 120 Watt Power Supply

    PoE Texas Gigabit 16-Port PoE Injector with 48V 120 Watt Power Supply

    $181.99

    PoE Texas Gigabit 16-Port PoE Injector with 48V 120 Watt Power Supply is capable of powering IP cameras, desktop phones, WiFi access points, or other low voltage devices through a network data cable using this Power over Ethernet (PoE) injector. The PoE Injector takes power from the 48 volt power supply and adds it to the Ethernet data cable (Cat5, Cat5e, Cat6) to your device.
    Specifications
    • Certifications: UL/CE/FCC • Data + PoE Ports 16 • Data Ports: 16 • Data Rate: Gigabit • Dimensions: 20x4x1.75 in. • Max Amps Per Kit 2.5 Amps • Max Power for Kit 120 Watts • Max. Amps Per Port: 650 mA • Mount Type: rack • Operating Humidity: 5% to 90% • Operating Temperature Range: -10 - 60C • Output Voltage: 48 volts • PoE Method Passive • PoE Mode/Pin-out: Mode A (-1,2 +3,6) • Power Input: 2.1mm DC x2 • Power Supplies: WS-PS-48v120w Learn More »
  6. GPOE-12AB-48V120W PoE Texas Gigabit 12-Port PoE Injector with 48V 120 Watt Power Supply

    PoE Texas Gigabit 12-Port PoE Injector with 48V 120 Watt Power Supply

    $166.99

    PoE Texas Gigabit 12-Port Poe Injector with 48V 120 Watt Power Supply is capable of powering IP cameras, desktop phones, or other low voltage devices through a network data cable using this power over Ethernet injector. A Passive PoE injector always delivers the same voltage as its power source. Pair this injector with a 48 volt DC power supply to power devices labeled “802.3af”, or you can use a 24 volt power supply with 24-volt passive PoE devices like Access Points from Mikrotik, Ubiquiti, and many more.
    Specifications
    • Certifications: UL/CE/FCC • Data + PoE Ports: 12 • Data Ports: 12 • Data Rate: Gigabit • Dimensions: 20x6x1.75 in. • LEDs Per Port 1 • Max Amps Per Kit: 2.5 Amps • Max Power for Kit: 120 Watts • Max. Amps Per Port: 650 mA • Mount Type: rack • Operating Humidity: 5% to 90% • Operating Temperature Range: 0-65C • Operating Temperature Range: 0-65C • Output Voltage: 48 volts • PoE Method: Passive • PoE Mode/Pin-out: Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8) • PoE Standard: 802.3af • Power Input: 2.1mm DC x2 • Power Supplies: WS-PS-48v120w • Weight (metric): 87oz Learn More »
  7. AT-8-56v120W PoE Texas Gigabit 8-Port PoE Injector with 56V 120 Watt Power Supply

    PoE Texas Gigabit 8-Port PoE Injector with 56V 120 Watt Power Supply

    $155.95

    PoE Texas Gigabit 8-Port PoE Injector with 56V 120 Watt Power Supply.Use these 56 volt Power over Ethernet (PoE) devices with high-powered Access Points and PTZ cameras. These fully IEEE 802.3at compliant injectors work with Cisco products and any other IP cameras, VOIP phones, WiFi access points required 802.3at or 802.3af PoE. With this PoE Injector, you can add power to your data cable for a fraction of the cost of upgrading to a PoE capable network switch.
    Specifications
    • Certifications UL/CE/FCC • Data + PoE Ports 8 • Data Ports: 8 • Data Rate: Gigabit • Dimensions: 8x4x4 in. Max Amps Per Kit 2 Amps • Max Power for Kit 120 Watts • Max. Amps Per Port: 550 mA • Mount Type: wall • Operating Humidity: 5% to 90% • Operating Temperature Range: -10 - 60C • Output Voltage: 56 volts • PoE Method: Active • PoE Mode/Pin-out Mode A (-1,2 +3,6) • PoE Standard: 802.3at • Power Input: 2.1 mm DC and Phoenix Connector 1840382 • Power Supplies: WS-PS-56v120w Learn More »
  8. POE-24-48V120W PoE Texas 24-Port PoE Injector with 48V 120 Watt Power Supply

    PoE Texas 24-Port PoE Injector with 48V 120 Watt Power Supply

    $154.99

    PoE Texas 24-Port PoE Injector with 48V 120 Watt Power Supply is capable of powering IP cameras, desktop phones, WiFi access points, or other low voltage devices through a network data cable using this Power over Ethernet (PoE) injector. The PoE Injector takes power from the 48 volt power supply and adds it to the Ethernet data cable (Cat5, Cat5e, Cat6) to your device. Save big on network upgrades and device installations Power over Ethernet delivers power 328 feet from the PoE Injector, eliminating the expense and hassle of installing AC power near your powered device. With this PoE Injector, you can add power to your data cable for a fraction of the cost of upgrading to a PoE capable network switch.
    Specifications
    • Certifications UL/CE/FCC • Data + PoE Ports 24 • Data Ports: 24 • Data Rate: 10/100 • Dimensions: 20x4x1.75 in. • Max. Amps Per Port: 650 mA • Mount Type: rack • Operating Humidity: 5% to 90% • Operating Temperature Range: -10 - 60C • Output Voltage: 48 volts • PoE Method: Passive • PoE Mode/Pin-out Mode B (+4,5 -7,8) • Power Input: 2.1mm DC, screw terminal Learn More »
  9. tycon

    Tycon Power 56V 100W High Power Gigabit POE Power Source/Inserter

    $151.95

    The TP-POE-HP-56G PoE is a quality Gigabit midspan power source, designed for years of reliable operation even in the toughest conditions. They accept data-in to a shielded RJ45 Jack and provide surge protected data-out and power on the shielded RJ45 output jack. They work by supplying power to the remote device on all 8 Ethernet wires. The Ethernet spec supports distances up to 100m (328 feet). The units are autoranging so that they accept AC inputs from 90VAC to 264VAC (50/60 Hz) and they supply regulated 56VDC at the output. They have various protections for surge, short circuit, overload and overvoltage. They have total power output up to 100W. Product Features • 100W Power • Remotely Power Equipment thru CAT5 Cable up to 100m • Built in Ethernet and AC Surge Protection • Autoranging Switching Power Supply • Short Circuit, Over Current and Over Voltage Protection • 10/100/1000Mb Compatible • High Temperature Industrial Operation • Compact size – Floor / Desktop / Wall Mount Product Applications • Wireless Access Points and Client Devices • IP Phone and Security Camera Systems Product Specifications • 90-264VAC 47-63Hz • PoE Output: 56VDC 1.8A 100W on all 8 wires • PoE Type: Passive • Max Inrush Current: 30A • Efficiency: 85% • Line / Load Regulation: 1% / 5% • Ripple / Noise: 1% / 2% • Protections: Over-Voltage, Short Circuit, Over-Current • Surge Protection:    - Ethernet: 4 Pin (1/2, 3/6) Common Mode Protection, 7.5V Clamping VOltage 5.4A (8/20us) Peak Pulse Current, <2pF Shunt Capacitance    - AC Input: Operating Voltage = 385VDC, Clamping Voltage = 775VDC, Maximum discharge current is 1200A (8/20us) • Certifications: FCC, CE • EMC Standards: FCC Class B EN55022 Class B • Safety Standards: UL1950, CSA 22.2 & TUV EN60950 • Environmental Standards: ROHS • Operating Temperature: -40 to 60°C (-22 to 140°F) • Operating Humidity: 5% to 90% • Storage Temperature: -40 to 80°C (-40 to 176°F) • Case Size: 116 x 150 x 41mm (4.6 x 5.9 x 1.6") • Weight: 454g (16oz) Product Data Sheet Tycon Power Learning Center Presentation Learn More »
  10. Meraki MR Series PoE Injector 30W (US version)

    Meraki MR Series PoE Injector 30W (US version)

    Regular Price: $186.25

    Special Price: $125.75

    This product usually ships within 3-5 business days. The Meraki 802.3at PoE Injector provides a quick and easy way to power your Meraki Enterprise indoor access points. It allows delivery of both data and power to a Meraki access points over a single Ethernet cable, allowing deployment of devices exactly where they are needed to provide the best wireless coverage and at much lower installation cost. This PoE injector is specifically designed to meet the power needs of Cisco Meraki 802.3at-compatible devices. Check the access point specifications to ensure compatibility. Product Specifications: • Input voltage: 100V AC, 240V AC • Maximum input current: 0.8A • AC input frequency: 50-60Hz • Maximum output power: 30W • Compatible with 10/100/1000 Mbit/s Ethernet, full duplex • Operating temperature: 32 to 104deg F (0 to 40deg C) • Backwards compatibility with 802.3af MR series access points Compatible products: • MR18 • MR26 • MR32 • MR34 • MR66 • MR72 Specification Sheet: MA-INJ-4-US Data Sheet Warranty and Technical Support: Meraki warranty returns are handled by Cisco Meraki directly. For more information on returns or warranty information please visit: Cisco Meraki Support Learn More »

Items 1 to 10 of 66 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Grid  List 

Set Ascending Direction

Back to top